Posted on by

Setup the YIKESHU Black NES Case with Fan Control Board

YIKESHU Case Fan Control

In this post will cover the installation of the Fan control on the YIKESHU Black NES Case, this case includes a fan right out of the box, but simply connect the fan to the provided fan header will keep the fan constantly running whenever the power switch is pressed, there is actually a better way, by installing the mini-mods NESPi Fan Control Board you can control the fan to turn ON only when your Raspberry Pi reaches a designated temperature and turn back OFF once the system has cool down.

Step 1

Before you can install the NESPi Fan Control Board the pins where the fan connects to the YIKESHU Black NES Case need to be straight up as show on the images:

Step 2

The installation of the Fan Control Board is fairly easy, as use the built-in fan headers of your YIKESHU Black NES Case, SOURCE connector of the Control Board will be placed on top of the fan pins as displayed on the image below, make sure to bend the positive (+) side of the pin as shown on the picture, this will act as a locking clip to keep the Fan control board in place.

Warning!!!
Installing the NESPi Fan Control Board on the incorrect pins on the Raspberry Pi can damage your Pi!
Please use NESPi Fan Control Board Hardware and Software at your own risk. We do not take responsibility for any damages to your raspberry pi that may occur.
By installing and downloading our hardware and software you are agreeing to these terms.

Step 3

Connect the pin label FAN_CT on the PCB to GPIO 17 (RPI pin 11).


Step 4

Clipping the fan to the case, this fits pretty tight, but if you insert it on an angle, with one edge inside the clip, then you can press it into the other clip with a bit of prodding and poking.

Step 5

Insert the fan connector to the adapter on the Fan Control Board, make sure is firmly attached.

Step 6

Screw the top component of the NESPi Case to its base.


STOP!!
The following step, requires Raspbian, RetroPie, RecalBox or Batocera to be fully functional before you continue, if you have not completed the installation, please see our guide: Install RetroPie in your Raspberry Pi and Play your First Retro Game.

Step 7

Now that you have assembled your NESPi game console, it’s time to install and configure some files for the Fan Control Board to work along with the Fan and temperature control to keep your Raspberry Pi from overheating. Fortunately, you can do this via online with a one-line code install using wget and bash in the Terminal.
1. Connect your Rasptendo console to a monitor and a keyboard before powering your Raspberry Pi.
2. Connect your Rasptendo to the internet. You may access the internet via LAN or via WiFi.
3. Access the Terminal on your Raspberry Pi.

In the Terminal, type the following command:
For Raspbian and RetroPie:

wget -O - "https://github.com/mafe72/NESPi-Fan-Control-Board/raw/master/install.sh" | sudo bash

For RecalBox:

wget -O - "https://github.com/mafe72/NESPi-Fan-Control-Board/raw/master/recalbox_install.sh" | bash

For Batocera:

wget -O - "https://github.com/mafe72/NESPi-Fan-Control-Board/raw/master/batocera_install.sh" | bash

This will run a command that will automatically configure your Raspberry Pi 3 to access Fan Control Board. Your Raspberry Pi will automatically reboot in order for the changes to take place.

Step 8

After your Raspberry Pi has rebooted, the Fan Control Board is fully configured and will turn the fan ON once the Raspberry Pi temperature exceeded 55C and turn OFF when the temperature is under 40C.

If you want to change the way the fan control software handles your fan, please refer to our blog post: Adding a fan to your RetroFlag Case.

FAN CONTROL BOARD
Fan State Action
ON Fan will turn ON when the temperature exceeded 55C
SLEEP/OFF Fan will turn OFF when temperature under 40C

If you encountered problems during the installation process, refer to a more detailed instruction from our GitHub page.